Bathroom

Hiring an expert to repair bathroom tile can be expensive and time consuming. Repairing or replacing the tile in bathrooms may seem complex and unattainable but even the least experienced home owner can repair the tiles in any size bathroom with the right tools, instructions and a little elbow grease.

If the damage is minimal, painting the cracks in the tile with matching paint will be simpler than replacing the tiles. Purchasing Tiles And Tools

If the entire bathroom floor is being replaced, choose a grout to compliment the new tile. Replacing The Damaged Tiles

Once it has been removed; use the grout remover and putty knife to remove the old grout and adhesive. Continue in this same manner until all of the damaged tiles are replaced.

Nowadays, people spend ample time and money towards the decoration of their bathroom tiles. You can utilize the given below techniques to repair the bathroom tiles.

-Firstly, start by removing the broken tiles. Remove the excess grout near the tiles with help of a grout saw. Now, remove the tiles and remaining grout with help of a putty knife.

- Now, take a putty knife and chisel to even out the tile adhesive. You should consult a knowledgeable tile dealer before purchasing the adhesive.

- Then, fix the new tile on the surface from where the tile was removed.

- After 24 hours, prepare a grout mixture and fill the joints between the bathroom tiles with help of the grout. Don't forget to clean the excess grout from the tile surface.

Bathtub Installation

When installing a tub to replace an existing unit, the old bath tub needs to be disconnected and removed. Using as much assistance as is necessary, place the new bath tub into place and use shims to level it. After the tub is leveled and is adequately supported, the next focus is to connect the necessary plumbing.

The steps needed to connect the plumbing will depend on what is already present from the previous tub. Although the process of bathtub installation can be complicated, once you learn how to install a bath tub, you can save a great deal of money by completing the task yourself. If the old tub is readily accessible, the project can move speedily; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. This article will help you install a new bathtub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous water supply pipes.

New Bathtub, Hammer, Pipe Wrenches, Prybar, Safety Glasses, Level, Pliers, Adjustable Wrench, Putty Knife, Screwdriver, Cold Chisel, Tape Measure, Pipe Caps

Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions.

Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.

Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub).

Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Next, fit the end of the flexible overflow pipe to the overflow outlet. Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.

Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.

If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.

Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The supply pipes can later be connected to the other end. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use.

Bathtub

If you have a problem with your bathtub filling up with water when you take a shower, or maybe the water drains out when you're taking a bath, you may need to repair your bathtub drain. A few simple tools and a little bit of knowledge is all you need to repair your bathtub drain.

When you look at your bathtub drain, is there a level that will move the drain plug up and down? This unlevered drain is the easiest type to repair, so we will discuss that one first. To remove the unlevered drain, simply lift the stopper up and turn it in a clockwise motion to release it. Now, place the new drain into the tub.

If you have a levered drain, it will take a bit more work, but is still a fairly easy fix. After you have removed everything, you will need to repeat the cleaning process again before you replace the drain and lever. Scrub the lever assembly clean with a wire brush to help remove any build-up. Repairs in your house are always likely going to cost quite a bit of money.There are many ways to cut down on these repair costs by doing some house repairs yourself.One repair which you should consider doing yourself is a bathtub repair.

If the repair is minimal apply some of the DIY tips below. For the repair of impact damage and flaking on bathtubs with enamel, ceramic (porcelain) and acrylic surfaces.For this job you would need a repair paste suitable for porcelain, enamel and acrylic.a non yellowing repair spray(make sure about the non yellowing factor with the salesperson at your hardware store),some special sandpaper with minimal rub off on ceramic and enamelled surfaces and a wet/dry sandpaper for acrylic and fiberglass surfaces.

With minor defects use a touch up stick.

Pool

We all want a gorgeous pool, gorgeous from top to bottom that is. Routine cleaning comes with routine repair to achieve this. But how do you know when to repair a pool? A lot of people pay experts to execute their pool repair but it is 100% doable.

1. Pool plaster

2. Acrylic resin

3. Water

4. Plastic Prowl/s

5. Rubber/plastic gloves

6. A shot glass

7. Matching paint

It is impossible to effectively repair your pool if it still has water in it.

Next, acid wash your pool. Just be reminded to wear rubber gloves, a gas mask and safety goggles as you acid wash your pool.

Let your pool completely dry.

We are now ready to repair your pool. Look for cracks and holes on the surface and mark them. 8. Apply the mixture evenly and then let it dry.

Purchase a paint color that matches with the color of your walls, deck and steps. Apply paint on the holes and cracks that you have covered. With just a few simple steps, you can save money on your pool repair.

Repair Plumbing

The slew of guides and manuals that deal with every conceivable plumbing problem in and around your house are like a Godsend for harried homeowners. The simple, step-by-step instructions, along with detailed illustrations, guide you through these mundane yet monstrous problems.

Whether tips on understanding your home's plumbing system or the local plumbing codes, list of tools and safety equipment required before undertaking any project or even preparing for all kinds of repairs, you are hard-wired for success.

So who's kvetching about faucet repairs, leaky tanks and frozen pipes? Plumbing professionals are crying foul.

If you do this inspection well, you can ensure that minor repairs do not turn into major expenses. Sometimes, the plumbing problem may require less frequent monitoring, and sometimes, it may require more. If you feel qualified that you can inspect the plumbing problems and perform a fix-it-yourself plumbing leak, you can certainly go ahead.

A professional plumber will not only spot any problems, but he will also advice on repairs and costs right on the spot. If you want a thorough evaluation, you can hire a home inspector. Take time to repair leaky faucets and caulk bathroom fixtures.